accessories
|
CS1001 Analog Probe
The CS1001 Analog probe is a switchable 1x /10x 250 MHz oscilloscope probe.
Specifications:
|
| Item |
Position x 1 |
Position x 10 |
 |
| Attenuation Ratio |
1:1 |
10:1 |
| Bandwidth |
DC to 6 MHz |
DC to 250 MHz |
| Rise Time |
58 ns |
2.3 ns |
| Input Resistance |
1 MΩ |
10 MΩ |
| Input Capacitance |
Approx 67 pF |
Approx 17 pF |
| Compensation Range |
|
10-35 pF |
| Working Voltage |
600V DC incl peak AC , derated to 50V at 10MHz and 10V at 100 MHz. |
| Safety |
Meets IEC1010-1 Cat 1. |
| Cable Length |
1.2 m |
|
Accessories that are included with probe are:Channel Identifier Clip, Sprung Hook, Ground lead, Insulating Tip, Adjusting Tool, Measuring Tip, Sprung Earth Tip.
|
|
|
|
CS1002 Analog Probe
The CS1002 Analog probe is a 100x 250 MHz oscilloscope probe.
Specifications:
|
| Item |
Performance |
|
| Attenuation Ratio |
1:100 |
| Bandwidth |
DC to 250 MHz |
| Rise Time |
1.4 ns |
| Input Resistance |
100 MΩ |
| Input Capacitance |
5.5 pF |
| Compensation Range |
10 to 35 pF |
| Working Voltage |
Cat II:1.5kV |
| Safety |
Meets IEC1010-1 Cat II. |
| Cable Length |
1.3 m |
|
Accessories that are included with probe are:Channel Identifier Clip, Sprung Hook, Ground lead, Insulating Tip, Adjusting Tool, Measuring Tip, Sprung Earth Tip.
|
|
|
|
CS1003 Analog Probe
The CS1003 Analog probe is a 1000x 50 MHz oscilloscope probe.
Specifications:
|
| Item |
Performance |
|
| Attenuation Ratio |
1:1000 |
| Bandwidth |
DC to 50 MHz |
| Rise Time |
<7 ns |
| Input Resistance |
100MΩ |
| Input Capacitance |
Approx 3 pF |
| Compensation Range |
5pF to 50pF |
| Working Voltage |
DC:1.5kV; AC Pulse: 30kV p-p; Sine Wave:10kV rms |
| Safety |
Meets IEC1010-1 Cat 1. |
| Cable Length |
2 m |
|
Accessories that are included with probe are:Channel Identifier Clip, Sprung Hook, Ground lead, Insulating Tip, Adjusting Tool, Measuring Tip, Sprung Earth Tip.
|
|
|
|
CS1004 + CS1005 Digital Probe Pods
The CS1004 + CS1005 Digital Probe pod is used to probe up to 8 digital signals. Eight signal and two ground probe clips are included.
Specifications:
|
| Item |
Value |
|
| Attenuation Ratio |
1:4 |
| Number of Signal Inputs |
8 |
| Probe Description |
45 mm Ezy™ Hook, spring probe, 0.4mm probe width |
| Bandwidth |
DC to 100 MHz |
| Rise Time |
2 ns |
| Input Resistance |
100 Ω |
| Input Capacitance |
Approx 16 pF |
| Working Voltage |
-16V to + 20V |
| Cable Length |
1 m from Cleverscope Acquisition Unit to Pod, 150mm from Pod to probe clip |
|
|
|
|
CS1010 Delay Line
A 5nsec delay line to connect the A and B channels together. By using the interleave function in the maths equation builder an effective 200 MSample/sec is available
|
|
|
|
CS1040 Isolated USB Cable
Isolated USB 1.1 interface cable. Minimum 2.5kV Isolation. Avoids potential for ground loops, ESD or introduced noise problems.
Comes with either a replacement USB module to provide power for units with serial numbers above 4000 or a plug pack supply for serial numbers below 4000. We will contact you before supplying to clarify which you need. If supplied with a new unit then the modified interface board will be installed at the factory.
|
|
|
|
CS1020 Link Cable
A short cable to connect two Cleverscopes together via the DIG I/O ports. It allows the trigger from one unit to trigger the channels of the other. It does not matter which way round it is used.
|
|
|
|
CS1001
CS1002
CS1003
CS1004 + CS1005
CS1010